How to start playing online games. Programs for playing over the Internet and local network How to start a local network game
To play any game local network, you must first configure this very network. In this article we will tell you how you can set up a local network in various operating systems, as well as between them.
In order to connect 2 computers in one room into a local network, you don’t need anything else except 1 RJ-45 cable, connect the 2 computers with a wire and set up the network.
Let's consider several connection options:
- Setting up and connecting 2 or more computers to a local network on Windows XP
- Setting up and connecting 2 or more computers to a local network on Windows Vista
- Setting up and connecting 2 or more computers to a local network on Windows 7
- Setting up and connecting 2 or more computers to a local network between Windows XP and Windows 7
- Setting up and connecting 2 or more computers to a local network on OS Windows 8.x
- Setting up and connecting 2 or more computers to a local network on Windows 10
There can be from 2 to 254 computers on a local network, I think this is enough to play with friends :) The network address should not start with 127.*.*.*, because reserved for testing and not available for use. Otherwise, you can use any IP addresses, but we recommend starting your addresses with 192.168.1.1, as this is the standard for small local networks.
To connect more than 2 computers to the network, you will need one of the options:
1. Additional input for a network card. (apartment, office)
2. Use a "switch". (apartment, office, entrance)
3. Use a router. (apartment, office, entrance, house, street)
A little more detail about each option:
1. Not everyone can insert another network card into a computer; there must still be room for it in the system unit, and if you connect laptops, then the option is a failure.
2. A switch is an additional device with which you can connect a different number of computers to the network depending on the switch model, usually from 4 to 48. You can use a circuit of several switches, connecting them in series, thereby increasing the number of computers in the network.
3. Router or (router). The ability to network computers both wired and wirelessly, depending on the router model. The big advantage of this device is that you only need to configure it once, and connect computers to it, and the router will distribute the settings to all computers on the network automatically, regardless of the installed operating system.
February 11, 2014
Online game in cs 1.6 without a doubt one of the most important aspects. An online game can be played either via the Internet or via local network. With the Internet, everything seems to be more or less clear; there are a great many ways to find a server to play over the Internet. How are things going with playing locally? What to do if you want to play with a person who is in close proximity to you? Or maybe you actually live in a student dormitory and dream of organizing a communal server? There may be many options, but it is not always possible to realize your plans. So let's get started.
Step 1. For local network games, of course we will need client cs 1.6. You definitely won’t have any problems with this, because you can always choose from our portal, choosing exactly what you like. And finally, the second thing we need is the local network(this could be a wifi router, router, etc.), to which all users who want to play are connected.
Step 2. Next, in the simplest scenario, after installing and launching the game, you need to click New Gam e (Depending on your build, this item may be called differently. Most often, it is located at the very top of the game menu).
Step 3. In the window that appears, configure the server. Selecting a card, round time, amount of money at the start, etc. Then click Start.
All. The server should appear in the Lan tab (menu Find servers->Lan), and your friend with whom you wanted to play online can connect to the server in this way.
Everything seems simple, but there are a number of problems that are difficult for beginners to cope with. Let's try to solve those that occur most often.
Possible difficulties when playing on a local network
Problem: The server is not visible in the Lan tab.
Solution: Try connecting to the server not through the game interface (i.e. not through the Lan tab), but by entering the command in the console connect ip:port. To find out the server address (ip:port) you can use in different ways. The simplest one is that the server administrator (the one who created the server) must enter the command in the console status, in response to which he will receive short information about the server and the players on it. In this small list there will be a very important item for us, which is called tcp/ip. Opposite it the IP and server port will be indicated in the ip:port format.
The second method is a little more complicated:
-Run command line Windows - start->run->cmd(on new versions of Windows you can write cmd directly in the start and press enter);
-In the window that opens (command line) write the command ipconfig ;
-The command line will respond with several lines. We are only interested in the line “ Link local IPv6 address" Opposite this line there will be your IP address in approximately the following format: 192.169.88.254 - this is exactly what we need;
As for the port, everything is much simpler here. Firstly, we can view it using the Status command on the server. Secondly, the port in almost 100% of cases is 27015.
So, to connect to a server that is not visible in Lan in this case, we need to enter the command “connect 192.168.88.254:27015” without quotes in the client console.
Problem: I did everything as stated above, but the connection to the server does not occur.
Solution: Most often in this case, the reasons may be a firewall, a third-party firewall, or an antivirus. We recommend that you disable these methods of protecting your operating system while playing.
Despite the fact that the word Firewall is quite scary, disabling it is quite simple.
— Go to the control panel.
- Find “Windows Firewall”.
— Double-click the left mouse button to open its settings
— On the left side of the menu, click Turn Windows Firewall on or off
— In each section, select Turn off Windows Firewall
After this, the firewall will be disabled.
To disable the firewall or antivirus (if any), the most common way is to right-click on the tray icon (bottom right - where the clock is) and click the “exit” or “pause protection” button.
There are situations when you need to turn on your computer remotely. This process is carried out using the Internet and requires preliminary configuration of equipment, drivers and software. We will talk in detail about launching a PC over a network through the popular remote control program TeamViewer. Let's look at the entire algorithm of actions in order.
The BIOS has a standard Wake-on-LAN tool, the activation of which allows you to start the PC over the Internet by sending a certain package of messages. The main link in this process is the above-mentioned TeamViewer program. Below in the picture you can find brief description algorithm for waking up the computer.
Awakening Requirements
There are a number of requirements that must be met in order for the PC to be successfully launched using Wake-on-LAN. Let's look at them in more detail:
- The device is connected to the mains.
- The network card has Wake-on-LAN on board.
- The device is connected to the Internet via a LAN cable.
- The PC is put into sleep, hibernation, or is turned off after "Start" — "Shutdown".
When all these requirements have been met, when you try to turn on the computer, the operation should be successful. Let's look at the process of setting up the necessary equipment and software.
Step 1: Activate Wake-on-LAN
First of all, you need to enable this function through the BIOS. Before you begin this process, double-check that you have the Wake on Internet tool installed on your network card. You can find out this information on the manufacturer’s website or in the equipment instructions. Next, do the following:
Step 2: Setting up the network card
Now you need to start Windows OS and configure the network adapter. There is nothing complicated about this, everything is done in just a few minutes:
Please note that you will need administrator rights to change settings. You will find detailed instructions on how to obtain them in our article at the link below.
Step 3: Setting up TeamViewer
The last step is to configure the TeamViewer program. Before this, you will need to install the software and create your account in it. This is done very easily. All detailed instructions you will find in our other article. After registration you should do the following:
Very often a situation arises when you want to play not only with bots, but also against each other online. To do this, you need a high-quality Internet connection and a company of three or four players. Our article talks about how to play over a local network.
Play online
- In order to play online, you need to make sure that all computers are connected to one network. To do this, open “Explorer” or “Total Commander” and check for the presence of computers in the “Network Neighborhoods” folder, where the MSHOME or WORKGROUP groups should be located.
- Next, you should open the game and create a new one. The computer on which the new game was created will be considered the main one. When creating new game You must specify the number of participants and a password to enter the game.
- Next, all participants must connect to the local network. To do this, select “Find servers” in the menu and click on the “Local network” tab. After the network loads, you must click “Join”.
Hamachi
You can also play on a local network using the Hamachi application:
- Download the program from softonic.com and install it on your computer.
- Open the program, hover over the triangle and select “Create a new network.”
- Enter your name and password.
- Go to a game where you can play online and create a local network.
- After this, friends must launch the program, enter the name and password (that you created) and start the game.
Multiplayer
Another option that allows you to play over a local network is the multiplayer games feature:
- Launch the game you are interested in.
- Select the multiplayer function.
- In the game creation menu, you need to select a map, set all the necessary parameters and settings. After this, you need to click “create server”.
- The game will load. All that remains is to dial required quantity players, as some games will not load without a certain number of participants. Players can communicate in a special chat.
If you want to connect to an already created game, you need to go to multiplayer and select “Connect to game”.
Technology remote activation(Wake on LAN) must be a supported BIOS and network card. Also, we will need a special application whose functions allow you to send a WOL packet to a remote PC.
Thanks to modern advances, you can turn on a remote PC not only from another computer, but also from your phone. It is also necessary to remember that turning on the computer remotely requires the activity of the network card - it must receive power in standby mode.
Preparatory actions
First of all, you need to configure the BIOS and network adapter to wake up. It doesn’t matter what kind of network it is - built-in or external. Having opened the main I/O program, we will find the section responsible for power management - Power Management, for example.
In this section you need to find the wake-up parameters.
These parameters can go by different names, including Wake on LAN, PowerOn By PCI Card, WOL from Soft-Off, and so on. This option must be enabled.
It is quite possible that you will need to enable the option in the picture below.
To be more confident, it's best to familiarize yourself with all the wake-up options in your BIOS. After all, the computer can wake up from the TV tuner if the option to turn on via PCI-Express is enabled, and after pressing any key on the keyboard if the options related to the PS/2 port are enabled. In our case, we need a parameter associated with the PCI bus on which the built-in network controller is located.
After setting up the BIOS, be sure to check whether the technology being discussed is supported by your Ethernet controller. We will need to enable the reception of the “magic” WOL packet so that the Ethernet controller is configured to wait for it. A WOL packet is a special Ethernet frame consisting of a sequence of bytes containing the MAC address of the network card. Having received such a frame, the Ethernet card generates a signal to wake up the PC.
So, let's open the network control center.
Let's open the properties of the network adapter.
Let's move on to its settings.
Let's enable WOL Magic Package and, if necessary, enable Energy Efficiant Ethernet, Termination Wakeup.
Let's go to the power management tab, where this configuration should be.
WakeMeOnLan
Let's use a small program called Wakmeonlan for our purposes. This application does not require installation. After it starts, you need to scan the local network so that Wakemeonlan finds all network devices.
It must work on a PC from which a WOL frame will be generated to turn on the remote PC. This is how Wakemeonlan scans:
If during the scan the application did not detect a currently disabled computer, then it is possible to add it yourself.
Let's add another device manually.
You just need to enter the IP address of this device and its MAC into the form.
Let's determine the addresses we need, for which we'll launch the command line.
Let's run ipconfig with the /all key.
The second way is to look at the “Adapter Status”.
Open the Details window.
Let's find the addresses that interest us.
Having added the desired device, we will update the list.
As you can see, we already have three devices.
After adding, you can easily turn it on remotely by clicking the “Wake up Selected Computer” button.
Let's use TeamViewer
The preliminary setup will allow you to launch the Wake on LAN function of an application such as TeamViewer. To remotely wake up your PC, you must ensure the following:
Cable Internet connection.
The computer is set to one of the modes: hibernation, sleep, or soft shutdown (Start and Shutdown).
Installed TeamViewer.
It is very important to disable Fast Startup in operating systems such as Windows 8 and 10. Your instances of TeamViewer must be associated with a program account. In this case, all devices must belong to the same LAN.
In the application options tab, you need to activate the Wake-on-LAN function and configure the configuration by clicking the button of the same name. By selecting the “Other applications on the same local network” option, add the TeamViewer ID of those devices that are allowed to wake up this computer. To create inclusion conditions using a public IP address, you will have to connect to dynamic DNS, which will also have to be configured on the network router. Let's consider all the steps in order.
First of all, let's connect all computers to an existing account.
Warning window about the need to connect to your account.
Linking using the “Link” button.
The established connection is displayed at the bottom.
We will need to configure the Wake on Lan function.
Check the box for other TeamViewer applications.
Add the TeamViewer ID whose computer will send the WOL packet.
You can wake up a remote PC from your account TeamViewer, where all devices linked to it are displayed. You just need to press a button in the form of a power button, which will send a WOL frame to the Ethernet card of the selected electronic device.
Brief summary
To turn on your PC remotely from another device, you need to configure the BIOS and Ethernet card. In the BIOS you will need to configure a policy for waking up the PC by a network signal, which is in an active state, provided by standby power. Also, you need to configure the Ethernet controller to receive WOL packets. You will also need a special program to generate a WOL package. Such a program could be, for example, Wakemeonlan or TeamViewer.